Malta Window Cladding

malta cladding stockMalta window cladding now available!  We are excited to announce we have received our first shipment of matching Malta window cladding for two popular vinyl clad Malta window models.  We now can offer after-market replacement cladded sash for Malta vinyl clad double hung windows and Malta vinyl clad casements shown below.

 

 

 

malta 200 clad casement 2malta 200 clad casementmalta 200 clad casement interior The vinyl clad casement shown here has a mitered corner, foam filled perimeter weatherstrip and an interior glass stop.  Fenster part number MT200-C.

 

 

 

[caption id="attachment_1561" align="alignleft" width="150"]OLYMPUS DIGITAL CAMERA OLYMPUS DIGITAL CAMERA[/caption] [caption id="attachment_1560" align="alignleft" width="150"]SONY DSC SONY DSC[/caption]

malta dh wet end view

 

The vinyl clad double hung shown here is a boot glazed window with a sharply mitered corner on the lower sash.  Most models had a torx screw as the lower tilt pin and a helicopter pin screwed in through the cladding on the upper.  This window was produced for many years from the mid 80’s through the mid 2000’s.  All looked the same, but with differences of note.  Earlier models were boot glazed with two different glass thicknesses.  The newer is a wet glazed sash with an interior glass stop.  The Fenster after-market unit will match the newer model with the interior glass stop, but WILL fit the older models since the sash profiles otherwise were not altered.  The Fenster part number for a complete cladded sash is MTDH250-C (upper or lower).

We are currently stocking WHITE Malta window cladding for both models.  Beige/sand can be special ordered with a minimum quantity of 10 sash.  Place and order request today at www.fensterUSA.com or email sales@fensterUSA.com

 

 

 

 

8 Comments

  • Posted May 15, 2016 at 6:29 pm | Permalink

    My window has a broken latch . Does the whole panel need to be replaced. It is the crank out that is not working….my window pane is not broken but I am not able to open and shut the window….

  • Posted May 15, 2016 at 6:31 pm | Permalink

    Where is the nearest dealer? I live ;in Clear Lake IA 50428

    • Posted May 16, 2016 at 1:36 pm | Permalink

      Phyllis, Sounds like a hardware issue. You shouldn’t have to replace the sash panel. Hardware is tricky to identify over the phone or email. We would need pictures of the parts in order to help identify them. Those can be sent to sales@fensterusa.com, or you might get a handyman or window expert involved to help you with this.

    • Posted May 16, 2016 at 1:39 pm | Permalink

      Phyllis, We do not have stores. All retail sales are done online from our headquarters in Indianapolis at https://www.fensterusa.com

  • Carl Pekol
    Posted October 5, 2018 at 2:26 pm | Permalink

    I need Malta window screens 35 3/4inches by 38 3/4 inches. most screens sold in Home Depot etc are Andersen and do not have these dimensions

    • Posted October 9, 2018 at 7:51 pm | Permalink

      Carl, I’m sorry, we don’t do screens. Ttry a smaller home town hardware store, not the big box guys.

  • Ed
    Posted December 6, 2018 at 11:37 am | Permalink

    Could you tell me aprox. how long it takes to receive the compression jamb liners after ordering?
    Also do you still make the cladding for Malta windows? Thanks. Ed

    • Posted December 6, 2018 at 1:11 pm | Permalink

      Hi Ed! Kind of a complex question. Lead times and availability are very specific to each product. A stock jambliner that we actually have in stock can turn in about a week. If we’re out of stock, and have to order from the factory, 3-4 weeks. If its a special order we don’t normally stock, then it could be as much as 6 weeks.

      The cladding question is similar. Technically we don’t make any of the cladding. It’s all from various suppliers. We have a specific model of vinyl clad (the chrysalis series I believe) that we do have the original cladding shape for. We have 2 other models, one vinyl clad, one aluminum clad that we’ve adapted to work with OUR aluminum cladding shapes, and then there are a couple extruded clad models that we can not do because the cladding shape is so unique that we can’t match it and it is not available from any other supplier. It really depends on what model you are looking for.

Post a Comment

Your email is kept private. Required fields are marked *